Q326 Tumble Belt Shot Blasting Machine — 200 kg per Batch
The smallest machine in our standard tumble belt range, and the one we hold in stock. One 7.5 kW blast wheel, a 200 kg batch, parts up to 600 mm long and 20 kg each. Ships in 7–10 days from order.

What the Q326 is actually for
A tumble belt machine cleans parts by turning them over against each other inside an endless rubber belt, under a blast wheel. It suits parts that can fall against each other without damage and that fit in the belt's working volume: small and medium castings, forgings, heat-treated parts, aluminium die castings, fasteners, brackets, and pressings.
The Q326 is the entry point of that range. Its limit is the batch: 200 kg, with no single piece heavier than 20 kg and nothing longer than 600 mm. If your part is bigger than that, the constraint is not the belt speed or the wheel — it is simply the wrong machine, and the Q3210 (600 kg, parts to 900 mm) is where the conversation goes next.
Full specification
| Parameter | Q326 |
|---|---|
| Roller length | 860 mm |
| End disc diameter | Φ650 mm |
| Working volume | 0.11 m³ |
| Max. single piece weight | 20 kg |
| Max. workpiece length | 600 mm |
| Max. batch load | 200 kg |
| Shot flow rate | 160 kg/min |
| Blast wheel power | 7.5 kW |
| Elevator capacity | 8 t/h |
| Separator capacity | 8 t/h |
| Dust extraction air volume | 2,000 m³/h |
| Total installed power | 14 kW |
| Overall dimensions (L×W×H) | 2,000 × 1,950 × 3,000 mm |
Values are the standard build. Wheel power, voltage, liner specification and the dust collector can be changed per order.
Why we keep this one in stock
Most of our machines are built to order, because most buyers arrive with a part that does not fit a catalogue size. The Q326 is the exception: it is the size that fits the widest range of small-part work, so we build it ahead of demand and keep it on the floor.
That changes the two numbers buyers care about most at the start of a project:
- Delivery: 7–10 days from order to shipment for a stock Q326. A custom tumble belt build is around 15 days.
- A machine you can see running before you commit, if you visit the factory in Botou — the stock unit is not a render on a spec sheet.
What is adjustable on a standard machine
- Voltage and frequency — 380V, 460V, 480V or 220–230V, 50 or 60 Hz, wired and tested to the site supply.
- Dust extraction — the machine is supplied with the extraction volume it needs (2,000 m³/h); the filter unit is sized to your shop layout.
- Liner specification — rolled manganese in the hot zone where the abrasive lands, NM500 elsewhere.
- Loading — manual loading is standard; automatic loading and unloading is available for a line.
Delivery, warranty and spare parts
- Delivery — stock Q326: 7–10 days to shipment. Custom tumble belt build: about 15 days.
- Warranty — 1 to 2 years depending on the application and how the machine runs; the terms are written into the quotation, not assumed.
- Wear parts — blast wheels, blades and liners ship by air freight, about 7 days to any country. These are the parts that wear in normal service, so they are kept ready rather than made to order.
- Payment — 30% T/T with the order, 70% before shipment.
Questions buyers ask about the Q326
Will my part fit?
Three limits decide it: 200 kg per batch, 20 kg per piece, 600 mm maximum length. Send the drawing and the batch weight and we will confirm — if it does not fit, we will say so and point at the Q3210 or Q3215 instead.
How long does a batch take?
It depends on how much scale or rust is on the part and the surface grade you need. Rather than quote a cycle time from a table, we test your parts and give you a real figure.
Is a bigger machine safer?
No. A 600 kg machine running 200 kg batches wastes power and floor space, and smaller parts tumble further and hit harder in a large drum. Size to the batch you actually run.
Compare it with the rest of the range on the tumble belt product page, or read Q326 vs Q3210 if you are between the two sizes. Not sure which machine type suits the part? Start with which shot blasting machine do I need.
Send Your Part Drawing