All Articles
Selection GuideNovember 2, 2026

Which Shot Blasting Machine Do I Need? Four Types, and Where the Line Falls

Tumble belt, hook type, mesh belt, roller conveyor. Almost every inquiry we get starts by naming one of these four — and sometimes names the wrong one. Here is how the choice actually resolves.

The machine type is decided by the part, not by the budget or the floor space. Four properties of the workpiece do almost all the work: how big it is, how heavy it is, whether it can be dropped against other steel without being damaged, and how many of them you make per shift.

MachineFitsDoes not fit
Tumble beltSmall and medium castings, forgings, die castings, fasteners, pressings — parts that can fall against each otherAnything fragile, precision-machined, or too heavy for the batch limit
Hook typeLarge, heavy or awkward parts that must not be tumbled: welded frames, castings with thin walls, machined surfacesHigh-volume small parts where cycle time per piece matters more than handling care
Mesh beltThin, flat and small parts that would fall between rollers or jam: stampings, springs, brackets, sheet cut-outsLong plates and structural profiles that need support along their length
Roller conveyorLong plates, H-beams, profiles and steel sections passing through in lineSmall parts that would drop between rollers, and thin sheet that sags

Tumble belt: the default for small castings

The work rides in an endless belt that turns it over continuously under one or two blast wheels. It is the cheapest way to clean a lot of small parts, and the reason foundries have used it for decades. The limit is physical: parts must survive falling against each other, and the batch must fit the belt's volume — 200 kg for a Q326, 600 kg for a Q3210, up to 1,000 kg for a Q3215.

What disqualifies it: a part with a machined face that cannot take impact, a thin-walled casting that will chip, a single piece over the weight limit, or a part longer than the drum.

Hook type: when the part must not be dropped

Parts hang from a hook and rotate through the blast stream. Nothing touches anything else, so a welded frame, a machined housing or a casting with a thin section comes out blasted without a single impact mark. This is the machine for the parts that tumble belt buyers come back for after they have seen the first sample.

The trade is throughput: one part, or one fixture of parts, per cycle. That is why hook machines dominate job shops and fabricators rather than high-volume foundries.

Where the line falls between hook and tumble belt is not a formula — it is a judgment on the part. Ask three questions: can it be dropped against other steel, is it heavier than the batch allows, and does its shape reach into the blast stream from every side while turning on a hook? If any answer is no, the tumble belt is out. We confirm that with the drawing before a machine is specified, because it is cheaper to argue about a drawing than a delivery.

Mesh belt: thin and small, one layer at a time

Parts lie flat on a wire mesh conveyor and pass through the chamber in a single layer. No tumbling, no jamming between rollers, and abrasive falls through the mesh instead of collecting on it. Stampings, springs, small brackets, sheet cut-outs and heat-sensitive parts belong here.

The boundary with the roller conveyor is simple and it is the one buyers get wrong most often: thin, small parts go on a mesh belt; long plates and profiles go on a roller conveyor. A 200 mm bracket on rollers falls through or tips. A 6 m beam on a mesh belt has nothing supporting it in the middle. Between those two cases the decision is about part length and how much support the part needs — not about which machine is bigger.

Roller conveyor: plate and structural steel, in line

Driven rollers carry plate, H-beams, angles and pipe through a chamber with wheels above and below. It is the only one of the four that scales to a steel service centre or a fabrication line, and the only one where the machine is usually part of a longer process — cutting, welding, painting.

The width of the roller table, the roller pitch and the wheel coverage across that width are what get specified. On wide tables the wheel count climbs, and so does everything that has to keep up with it — see how configuration drives the machine.

Three ways a machine ends up almost fitting

Almost every mismatch we are asked to correct comes from one of these three, and none of them is visible on a spec sheet until the part arrives:

  • Sizing to the average part instead of the largest. The batch limit is set by the heaviest single piece, not by the typical one. A shop that runs 8 kg parts and occasionally a 14 kg one needs the next size up, and will discover it on the first oversized order.
  • Buying throughput the process does not need. A machine twice the required capacity does not clean twice as well; it runs half-empty, wears its liners on the same path, and uses power for parts that are not there.
  • Treating fragility as a finish problem. Impact damage does not show up in a surface-grade check on the day of acceptance. It shows up three weeks later, in the scrap bin, after a hundred parts have been through the same cycle.

What to send us

  1. A drawing or dimensioned sketch, and the heaviest single piece
  2. How many parts per shift, or square metres per hour
  3. The surface grade — SA 2.5 or SA 3.0 — and what goes on afterwards
  4. Whether any surface is machined, ground or otherwise finish-critical
  5. Site voltage and frequency, and the space the machine has to fit into

With those five, the machine type is usually settled in one exchange. If it is not — if the part sits between two types — we say so, explain what each option costs you in handling or cycle time, and let you choose with the trade-off in front of you.

Questions we get asked

Can one machine do both small parts and large frames?
Not well. The handling that suits a batch of small castings damages a large frame, and the cycle that suits a frame wastes capacity on small parts. Shops that run both usually end up with two machines rather than one compromise.

Is the biggest machine in a range the safest choice?
It is the most expensive way to be unsure. A larger chamber than the part requires costs power, floor space and liner wear, and small parts tumble further and hit harder in a large drum.

What if my part is borderline?
Send it. We test on real parts rather than deciding from a table, and the answer sometimes is that neither machine is right and the part needs a fixture.

The four ranges are here: tumble belt, hook type, mesh belt and roller conveyor. If you already know the type and only need the size, Q326 vs Q3210 is the same argument one level down.

Ask an Engineer to Check the Part