All applications

Shot blasting for foundry castings: sand, scale, and the cost of cleaning too hard

A casting leaves the mould with two different things stuck to it, and they do not come off the same way. Burnt-on sand is chemically bonded into the skin and needs energy — velocity, angular abrasive, time. Mill scale is a brittle layer that comes off easily once the whole surface is covered — it needs coverage, not force. A machine set up for one of them usually does the other badly.

What is actually on the casting

Burnt-on sand sits where the metal was hottest against the mould — in corners, at ingates, on the drag face of a green sand mould. It is not dust; it is a glassy layer fused into the surface, and it is the reason a casting that looks clean still fails a coating test.

Core residue stays inside cavities and passages. If it is not removed before painting, it works loose later and takes the coating with it.

Parting line flash and fins are thin sections that blast removes slowly while the rest of the surface is already clean — which is why over-blasting thin edges is the most common quality complaint in a foundry.

Matching the machine to the casting

WorkpieceMachine
Up to 20 kg per piece, tough enough to tumbleTumble belt Q326 — 200 kg per batch
30–200 kg, irregular or thin-walledHook type Q376 / Q378 — Φ1000–1300 mm swing
600 kg batches of small castingsTumble belt Q3210 — 30 kg per piece
Up to 1,000 kg batchesTumble belt Q3215
Large single castings, crane-loadedHook type Q3740 / Q3750

The dividing line is not weight alone. A 15 kg thin-walled aluminium casting behaves nothing like a 15 kg grey iron one; the first needs lower wheel speed and finer abrasive, the second shrugs off both.

Why over-loading the chamber costs more than a second machine

A Q326 takes 200 kg per batch and 20 kg per piece, which is ten pieces per cycle — not twenty. Load it with fifteen and the parts sit on top of each other, the ones at the bottom of the pile never see the blast stream, and the cycle time gets stretched to compensate for the ones that do. The result is a machine running longer hours to produce a worse finish, with liners wearing on a schedule set by the overload rather than by the tonnage.

The same arithmetic points the other way when a machine is oversized. A Q3210 bought for a 15 kg part runs half empty: the belt turns, the wheels throw shot, and the wear parts age by cycle rather than by work done. Two small machines running full usually beat one large machine running at half load, and they fail one at a time instead of stopping the line.

Cleaning too hard: the defect nobody prices in

Shot blasting is also shot peening when the energy is high enough, and on a thin section that shows up as rounded edges, closed threads, distorted flanges and — in the worst case — a surface that passes the visual standard and fails dimensional inspection. Three settings control it:

Abrasive size. S330 and S280 cut heavy sand and scale; S170 and S110 do the same cleaning at lower impact energy on thin or machined surfaces. Choosing a finer grade costs cycle time and saves parts.

Wheel speed. A variable-frequency drive on the wheel motors lets the same machine run a gentle cycle for aluminium and a hard one for grey iron, instead of buying two machines for two materials.

Coverage versus dwell. Extra passes buy nothing once the surface is uniformly grey; they only round edges. The separator matters here too — at 99.5% abrasive purity, the wheel throws round, broken shot out of the stream before it can peen a machined face.

What the paint shop will ask you for

Visual cleanliness is only half the requirement. Coatings bond to a profile, and a surface that is visually SA 2.5 but too smooth will fail adhesion just as reliably as one with sand left on it. Castings for painting are normally specified at SA 2.5 / SSPC-SP10 with a profile around 40–80 µm, checked with a comparator and a profile gauge rather than by eye.

Dust extraction is part of that answer, not a accessory. An undersized collector leaves dust in the chamber, the operator cannot see the parts, and abrasive is carried out with the air instead of recirculating through the separator. The machines here ship with a collector sized to the chamber and a measured emission below 5 mg/m³.

Questions buyers ask about castings

Will blasting remove sand from internal passages?
It reaches what the abrasive can see. Open passages and accessible cavities clean properly; blind holes and long small-diameter cores generally need a shakeout or a water wash first. Tell us the geometry and the answer is specific rather than optimistic.
Can the same machine clean aluminium and grey iron?
Yes, with a drive on the wheel motors and the right abrasive grade. The risk is not mechanical, it is metallurgical: the settings that clean iron will round and peen aluminium, so the two materials are run as two recipes rather than one compromised setting.
How do I know the batch is clean without inspecting every piece?
Run a test batch at commissioning with your parts, agree a reference piece against an ISO 8501-1 photograph, and set the cycle to reproduce it. After that, the cycle time is the control — not the operator's judgment at the door of the machine.
What happens to the sand and dust that comes off?
It goes to the collector, and the separator returns usable abrasive to the wheel. That is why separator condition is checked at every service: a worn separator sends good shot to the dust bin, and consumption climbs without anyone noticing why.

Related: tumble belt range, hook type range, which machine fits your part, choosing abrasive.

Send a part drawing Structural steel instead